ServeRAID MR 10 k SAS/SATA Controller – Linux Installation Client and Basic Commands
This post show installation of MegaCli (ServeRAID MR 10 k SAS/SATA Controller client) and two basic commands
1. Installation
Get ServeRAID CD and extract the file MegaCli-X.XX.XX-Y.i386.rpm.
Install using the rpm command
# rpm -ivh rpms/MegaCli-3.00.07-1.i386.rpm
Preparing... ########################################### [100%]
1:MegaCli ########################################### [100%]
Listing the installed files with rpm command
# rpm -ql MegaCli
/opt/MegaRAID/MegaCli/MegaCli
/opt/MegaRAID/MegaCli/MegaCli64
2. Basic commands
a. Listing All informations
# /opt/MegaRAID/MegaCli/MegaCli-AdpAllInfo -aALL
Adapter #0
==============================================================================
Versions
================
Product Name : IBM ServeRAID-MR10k SAS/SATA Controller
Serial No : KNNNNNNNNN
FW Package Build: 8.0.1-0036
Mfg. Data
================
Mfg. Date : 07/06/04
Rework Date : 00/00/00
Revision No :
Battery FRU : N/A
Image Versions In Flash:
================
FW Version : 1.12.152-0440
BIOS Version : NT16
WebBIOS Version : 1.1-33e-e_11-Rel
Ctrl-R Version : 1.01-010B
Preboot CLI Version: 01.00-011:#%00001
Boot Block Version : 1.00.00.01-0011
Pending Images In Flash
================
None
PCI Info
================
Vendor Id : 1000
Device Id : 0060
SubVendorId : 1014
SubDeviceId : 0363
Host Interface : PCIE
Number of Frontend Port: 0
Device Interface : PCIE
Number of Backend Port: 8
Port : Address
0 5000c5000c627be9
1 5000c5000ca68091
2 5000c5000c60f9a1
3 5000c5000123bce1
4 0000000000000000
5 0000000000000000
6 0000000000000000
7 0000000000000000
HW Configuration
================
SAS Address : 5005076b08028540
BBU : Present
Alarm : Present
NVRAM : Present
Serial Debugger : Present
Memory : Present
Flash : Present
Memory Size : 256MB
TPM : Absent
Settings
================
Current Time : 14:56:28 1/9, 2009
Predictive Fail Poll Interval : 300sec
Interrupt Throttle Active Count : 16
Interrupt Throttle Completion : 50us
Rebuild Rate : 30%
PR Rate : 30%
Resynch Rate : 30%
Check Consistency Rate : 30%
Reconstruction Rate : 30%
Cache Flush Interval : 4s
Max Drives to Spinup at One Time : 2
Delay Among Spinup Groups : 12s
Physical Drive Coercion Mode : 1GB
Cluster Mode : Disabled
Alarm : Enabled
Auto Rebuild : Enabled
Battery Warning : Enabled
Ecc Bucket Size : 15
Ecc Bucket Leak Rate : 1440 Minutes
Restore HotSpare on Insertion : Disabled
Expose Enclosure Devices : Enabled
Maintain PD Fail History : Enabled
Host Request Reordering : Enabled
Auto Detect BackPlane Enabled : SGPIO/i2c SEP
Load Balance Mode : Auto
Use FDE Only : No
Security Key Assigned : No
Security Key Failed : No
Security Key Not Backedup : No
Any Offline VD Cache Preserved : No
Capabilities
================
RAID Level Supported : RAID0, RAID1, RAID5, RAID6, RAID10, RAID50, RAID60
Supported Drives : SAS, SATA
Allowed Mixing:
Mix In Enclosure Allowed
Status
================
ECC Bucket Count : 0
Limitations
================
Max Arms Per VD : 32
Max Spans Per VD : 8
Max Arrays : 128
Max Number of VDs : 64
Max Parallel Commands : 1008
Max SGE Count : 80
Max Data Transfer Size : 8192 sectors
Max Strips PerIO : 42
Min Stripe Size : 8kB
Max Stripe Size : 1024kB
Device Present
================
Virtual Drives : 1
Degraded : 0
Offline : 0
Physical Devices : 5
Disks : 4
Critical Disks : 0
Failed Disks : 0
Supported Adapter Operations
================
Rebuild Rate : Yes
CC Rate : Yes
BGI Rate : Yes
Reconstruct Rate : Yes
Patrol Read Rate : Yes
Alarm Control : Yes
Cluster Support : No
BBU : Yes
Spanning : Yes
Dedicated Hot Spare : Yes
Revertible Hot Spares : No
Foreign Config Import : Yes
Self Diagnostic : Yes
Allow Mixed Redundancy on Array : No
Global Hot Spares : Yes
Deny SCSI Passthrough : No
Deny SMP Passthrough : No
Deny STP Passthrough : No
Support Security : No
Supported VD Operations
================
Read Policy : Yes
Write Policy : Yes
IO Policy : Yes
Access Policy : Yes
Disk Cache Policy : Yes
Reconstruction : Yes
Deny Locate : No
Deny CC : No
Allow Ctrl Encryption: No
Supported PD Operations
================
Force Online : Yes
Force Offline : Yes
Force Rebuild : Yes
Deny Force Failed : No
Deny Force Good/Bad : No
Deny Missing Replace : No
Deny Clear : No
Deny Locate : No
Disable Copyback : No
Enable Copyback on SMART : No
Enable Copyback to SSD on SMART error : No
Error Counters
================
Memory Correctable Errors : 0
Memory Uncorrectable Errors : 0
Cluster Information
================
Cluster Permitted : No
Cluster Active : No
Default Settings
================
Phy Polarity : 0
Phy PolaritySplit : 0
Background Rate : 30
Stripe Size : 128kB
Flush Time : 4 seconds
Write Policy : WB
Read Policy : None
Cache When BBU Bad : Disabled
Cached IO : No
SMART Mode : Mode 6
Alarm Disable : Yes
Coercion Mode : 1GB
ZCR Config : Unknown
Dirty LED Shows Drive Activity : No
BIOS Continue on Error : No
Spin Down Mode : None
Allowed Device Type : SAS/SATA Mix
Allow Mix In Enclosure : Yes
Allow HDD SAS/SATA Mix In VD : No
Allow SSD SAS/SATA Mix In VD : No
Allow HDD/SAS Mix In VD : No
Allow SATA In Cluster : No
Max Chained Enclosures : 16
Disable Ctrl-R : Yes
Enable Web BIOS : Yes
Direct PD Mapping : No
BIOS Enumerate VDs : Yes
Restore Hot Spare on Insertion : No
Expose Enclosure Devices : Yes
Maintain PD Fail History : Yes
Disable Puncturing : Yes
Zero Based Enclosure Enumeration : No
PreBoot CLI Enabled : Yes
LED Show Drive Activity : No
Cluster Disable : Yes
SAS Disable : No
Auto Detect BackPlane Enable : SGPIO/i2c SEP
Use FDE Only : No
Delay during POST : 0
Exit Code: 0x00
b. Show rebuild details from disks
# /opt/MegaRAID/MegaCli/MegaCli -PDRbld -ShowProg -PhysDrv [0:0] -aALL
Device(Encl-0 Slot-0) is not in rebuild process
Exit Code: 0x00
# /opt/MegaRAID/MegaCli/MegaCli -PDRbld -ShowProg -PhysDrv [0:1] -aALL
Device(Encl-0 Slot-1) is not in rebuild process
Exit Code: 0x00
# /opt/MegaRAID/MegaCli/MegaCli -PDRbld -ShowProg -PhysDrv [0:2] -aALL
Device(Encl-0 Slot-2) is not in rebuild process
Exit Code: 0x00
# /opt/MegaRAID/MegaCli/MegaCli -PDRbld -ShowProg -PhysDrv [0:3] -aALL
Device(Encl-0 Slot-3) is not in rebuild process
Exit Code: 0x00
-
1
Pingback on set 16th, 2012 às 3:03 am
[…] ServeRAID MR 10 k SAS/SATA Controller – Linux Installation Client … […]
Deixar mensagem para kairo Cancelar resposta
Unix, AIX, Linux, Storage Disk, Storage Area Network (SAN), HMC, Blade Center, IBM, TI, SysAdmin, Computação e Pessoal
UNIX (Linux, AIX, Solaris, HP-UX) Specialist at TIVIT
Note: All information and opinions in this blog / website are purely personal and do not reflect any opinions or information from TIVIT.
Nota: Todas as informações e opniões neste blog/website são meramente pessoais e não refletem quaisquer opniões ou informações da TIVIT.
Fast Blog (Pessoal)- Ocorreu um erro. É provável que o feed esteja indisponível. Tente mais tarde.
Kairo Araujo 
24/02/2010 at 10:31 pm
Hello everyone! I do not know where to start but hope this site will be useful for me.
Hope to receive some assistance from you if I will have any quesitons.
Thanks and good luck everyone! 😉
25/02/2010 at 1:42 am
Hi.
Thanks. Its a simple personal unix notes.
I need plubish new notes…. 🙂
12/08/2010 at 11:31 pm
hi everybody
Just saying hello while I read through the posts
hopefully this is just what im looking for, looks like i have a lot to read.
04/09/2010 at 9:12 pm
Anyone need links back to your web pages? will give you hella of backlinks. e-mail: webmaster@spreadrumers.com. Dueces!